DIY Menstrual Cups & Hack4Fem

Background on Menstrual Cups

I’ve been throwing around the idea of customized or instrumented menstrual cups for a while.

Menstrual cups, typically made of medical-grade silicone, are cups that catch the blood flowing out of the cervix and typically only need to be emptied twice a day. They are flexible so you fold them and they open on insertion. They exist in collapsible, ball-valve, and other forms.

For why I love them (well, I actually switched to tampons first):

so recently I started regularly using tampons, they are amazinnnnggg

seriously
every month my sleep schedule would get massively disrupted, because I slept uneasily, sometimes even in an upright sitting position, ready to jump awake when blood inevitably started to go everywhere, and also I’d have to wash my sheets and multiple sets of underwear / pants each month, often by hand
or i’d store pads in my bookbag and a month later when I needed them again, they’d be full of resistors and other bookbag filth, since the pad packaging isn’t really watertight

Some of my friends like the concept of menstrual cups, but have various problems with removal and leakage. I speculate that custom cups could help, although more analysis is needed to determine the cause and the variation. Hence this project.

I also really like the idea of an citizen science project measuring variation in periods. Other people claim a Diva cup is supposed to hold half your period’s worth of blood — I definitely bleed at least four cup-fulls during my period, so I wonder if my bleeding is heavy. If lots of people contributed data, we could see whether it varied by ethnicity, age, body weight, etc. It would be a ton of fun!

I was beaten to the punch on instrumented cups, but I think there is still room for improvement (or at least an open-hardware version).

This past Saturday I ran a hackathon for feminism (website here).

2015-11-14

It went really well, and I’ll blog about it in another post shortly — this one’s focused on menstrual cups 🙂

hackathon

pre-hackathon

Before the hackathon, John and I made menstrual cup molds and cast menstrual cups. We modeled it in Solidworks, then intersected it with a rectangular prism and split the prism in half. This created a two-part mold with a cavity in-between the size and shape of the menstrual cup. The Solidworks 2015 files are available here and are CC-BY-SA (c) John Aleman.

model

We then printed these out on a Stratasys printer, melted the wax support material off in the toaster oven, cleaned off with isoproprly alcohol, and had our molds.

2015-11-12

I first tested it at home with John’s help. We used Smooth-On’s SORTA-Clear Translucent Silicone Rubber, shore 37, since it cures in 4 hours instead of 24 hours. This is food safe and I think body-safe — I would call Reynold’s Advanced Materials to double-check before actually using one of these cups.

Turns out this material was really difficult to work with… it was the consistency of viscous snot.  No pictures pre-hackathon since the silicone is messy. I sure had a difficult time separating the molds. And it turned out we hadn’t even filled the molds for two of them!

incomplete-molds

Eventually some careful prying by my friend Nadya, we opened the final mold to find a menstrual cup inside!

mcup-mold

mcup

It had a lot of bubbles — would have benefited from 2-3 minutes in a vacuum. Unfortunate, since there doesn’t seem to be a cheap hobbyist vacuum solution. It was also slightly tacky, so either something in the 3d print is inhibiting cure or we didn’t mix well enough.

hackathon hands-on workshop

hackathon-molds

At the hackathon, we used syringes to eject into the molds until it came out the sides, and also just poured it into the bottom half of the mold and squeezed the top half on top to guarantee the mold was filled. We also all got pretty excited about the idea of glittery menstrual cups! 🙂 Sadly I didn’t have glitter on hand.

twocups

 

At the end of the hackathon we managed to demold one. This one  also had a giant bubble and many little bubbles, and was also tacky after the full four hours of cure time. We mixed this one much better, so I’m starting to think something is inhibiting cure, or perhaps the place we left them was too chilly.

next up

I definitely need a better mold design, and I need to figure out why the silicone is not curing properly. I also need to figure out a way around the bubble issue.

I also wonder how to analyze and determine why menstrual cups are failing (when they are hard to retrieve or leak). I also wonder, if fit is part of the problem, how you could easily take a measurement(s) to customize menstrual cups to each person.

And of course, I want to build the open science project! 🙂 Maybe instead of having each person build their own cup, I could at least start a form going and collect data…

3 thoughts on “DIY Menstrual Cups & Hack4Fem”

  1. There are some cheap DIY vacuum solutions (I mean, if you’re using a Stratasys already). In any case, when we pour in epoxies to mix we want to make sure there’s a minimal amount of air bubbles in them before we apply them to composites. In one of our labs, we have this ghetto setup. We’re talking : a paint bucket, with several holes drilled into it to connect a gauge pressure, a filtered air pump, a transparent lid just to see what’s going on in the inside, and hose clamps with seals around the entries to keep it air tight.

    Concerning the mold, have you considered giving the surfaces of it an acetone treatment?

    1. Hey, thanks, I’ll look into such a setup. The molds actually came out pretty smooth so we didn’t think the acetone was worth it.

  2. Wow cool!
    As for cups holding an entire period’s worth, the guesstimate that we lose 30 ml monthly is really pointless. It was based on weighing used tampons and pads, and it was supposed to be blood only, not other stuff you lose. Many cuppers lose 30 ml daily or several times a day even, and losing 300+ ml per cycle isn’t unheard of, though that’s definitely heavy (some endo sufferers report that).

Comments are closed.